These topics include IPv4 and IPv6 network configuration, managing TCP/IP 1. Oracle Solaris TCP/IP Protocol Suite (Overview) The default is 10 seconds. Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the.

Author: Kagadal Kimuro
Country: Syria
Language: English (Spanish)
Genre: Technology
Published (Last): 5 September 2017
Pages: 105
PDF File Size: 8.30 Mb
ePub File Size: 7.79 Mb
ISBN: 343-1-35192-483-8
Downloads: 23360
Price: Free* [*Free Regsitration Required]
Uploader: Voodoogal

If one of the group names contains a space, these group names look the same in the status display. Introductory information about DR and the cfgadm command. If no replies are made in response to five solariw probes, in. The same non-null character string IPMP group name identifies all interfaces in the group.

Failover is the automatic process of switching the network access from a failed interface to a functioning physical interface in the same group. Link-based failure detection, if supported by the NIC driver Probe-based failure detection, when test addresses are configured Detection of interfaces that were missing at boot time The in.

The standby interface in an IPMP group is not used for data traffic unless some other interface in the configurtaion fails. What Happens During Interface Failover The following two examples show a typical configuration and how that configuration automatically changes when an interface fails. Detaching NICs All requests to detach system components that contain NICs are first checked to ensure solarid connectivity can be preserved.

  EXERCICE TURBOMACHINERY PDF

How to configure Solaris 10 IPMP ?

For example, a qfe NIC can have four interfaces, qfe0 through qfe3and so on. IP Security Architecture Overview.

Configure the interface with a test address These physical interfaces might or might not be on the same NIC.

Create an IPMP interface group. The Primary Administrator role includes the Primary Administrator profile.

When the repair of a failed interface is detected, network access fails back to the repaired interface, as described in IPMP Failure Detection and Recovery Features. Data Addresses Data addresses are the conventional IPv4 and IPv6 addresses that are assigned to an interface of a NIC at boot time or manually, through the ifconfig command.

The default value for failure detection time is ippmp seconds.

Then, the standby interface is treated the same as other active interfaces until the failed interface is repaired. Because IPv4 addresses are a limited resource for many sites, you might want to use non-routeable RFC private addresses as test addresses. Administering Mobile IP Tasks.

How to configure Solaris 10 Probe based IPMP

Network Interface Card A network interface card is a network adapter that can be built in to the system. RCM has no information regarding how to configure the interface. Preventing Applications From Using Test Addresses After you have configyration a test address, you need to ensure that this address is not used by applications.

The Primary Administrator role includes the Primary Administrator profile. For example, you cannot place an ATM interface in the same group as an Ethernet interface.

  MAJORING IN PSYCHOLOGY HELMS PDF

Modifying IPMP Configurations – System Administration Guide: IP Services

Occasionally, a physical interface or the networking hardware attached to that interface might fail or require maintenance. An IPMP configuration typically aolaris of two or more physical interfaces on the same system that are attached conriguration the same IP link. After the daemon receives 10 consecutive replies for a default repair detection time of 20 seconds, the daemon determines that the interface is repaired. If no routers exist on the link, in. Its very clear and simple.

The failure and repair detection times apply only to probe-based failure detection. Troubleshooting Network Problems Tasks. Configuring an IPv6 Network Tasks. Administering Network Interfaces Tasks 7. The ifconfig status display does not show spaces. IP Security Architecture Reference To identify the link-local ipm; of an interface, run the ifconfig interface command on an IPv6-enabled node.

You can observe this flag in the status lines for the interface in the ifconfig output. If the cable for bge0 is unplugged, then configjration failure detection will report both bge0 and bge as having instantly failed. If the checks are successful, the data addresses associated with the detached NIC fail over to a functioning NIC in the same group, as if the NIC being detached had failed.