Aquamist Manuals HFS-6 HFS-5 HFS-4 HFS-3 HFS-2 HFS-1 MF2 DDS3. As water injection is playing a more and more important role in power tuning, there is more need to have a “fail-safe” mechanism in place to detect the presence. Aquamist HFS3 – UPDATE installation completed w. picts . marketed the Aquamist 1s system with Volvo specific instructions and people were.
|Published (Last):||17 November 2010|
|PDF File Size:||5.41 Mb|
|ePub File Size:||16.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
How hard is the install? It uses the washer fluid tank with a separate pickup for methanol and another tap for the flow sensor. I like the controlled flow.
I also like the idea of the regulated flow from this system, its the only way to mxnual water injection the right way. With more than 2 million posts our community is one of the most active groups of Volvo owners in the world.
Moreover, it will help you with the initial trim adjustments as you’ll need easy access to the controller. Stock S60r Totalled: Also at high speeds the 5th and 6th gear seems better with improved throttle response and power maybe from the lower IATs and more denser air?
See product comparison tab above for a comprehensive list of features and functions offered by other companies. I’ve have mine half installed at the moment. Find More Posts by dlbrooks Originally Posted by StealthyS60R. Find More Posts by marv Find More Posts by Mamual. Originally Posted by AcExSpades. This system is a bit more refined.
Hffs-3 of the factory wire bundles might be shielded, I haven’t taken them apart to know for sure though. Stealthy, your point is noted, and I appreciate the heads up. Originally Posted by marconi Find More Posts by bmwe I could have sworn, a long, long aquaist ago, that Lucky IPD calculated. It seems like on of those items that picks the name of the main stream product I helps that my specialty while getting my aero degree was designing things like guidance and instrumentation systems, so I’m trying to pass on some valuable info here so someone doesn’t accidentally create any electrical gremlins for themselves.
Aquamist HFS4 Methanol Injection for BMW Direct Injection Engines
The time now is I’m aquamjst thinking of doing this. Perhaps this is why none of these “mods” are really scarya challengeor serious. Originally Posted by bmwe82 Yes it intercepts the wastegate signal wire.
If a single unshielded wire will be used, be careful to not run it near any wire busses that carry quickly varying loads like the coil or injector driver circuits and try to keep it as short as aquuamist.
How is it holding up? There are so many places to hide the module and you chose that one! Not to knock the Aquamist system or anything but why is that most of the people on here are die hard “Aqua Mist” Fans. I’d normally change out all drive train fluids once per year, i.
Volvo seems to have gone away from shielding in favor of the twisted pair it seems, I will look sometime but if I remember right only sensors in the engine get it. The MAP has to represent a 3 BAR of pressure range with only 5 volts of signal range so any intefering voltage levels that get added or subtracted from that will give the ECU boost values that randomly deviate from the actual value. User manual April on: Find More Posts by Eliei. Fixed magnetic fields and non moving wires are fine, but its magnetic flux across the wires will generate signals that could cause issues.
Originally Posted by bmwe Find More Posts by Syndicategt. Never run lean, i. Meth kit ECU wiring Like this meth kit.
Today’s newer, knock-sensor-equipped vehicles are very good at staving off detonation by retarding ignition timing the moment detonation-also known as “knock”-is detected, but do so at the cost of severely decreased power output and fuel economy. There are so many other locations to install a switch and now you taken the function of trunk opener out! Originally Posted by cnic Congrats on the kit If you just twist wire and tape it, then you are most likely going to have an issue.