Buy ASME NQA Quality Assurance Requirements For Nuclear Facility Applications from SAI Global. ASME NQA-1– (Revision of ASME NQA-1–). Quality. Assurance. Requirements for. Nuclear Facility. Applications. AN AMERICAN NATIONAL. American Society of Mechanical Engineers (ASME) NQA (95 addenda) and editions. The requirements of these documents shall be complied with .
|Published (Last):||17 April 2004|
|PDF File Size:||6.38 Mb|
|ePub File Size:||16.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
A very high level of cleanness as evidenced by the freedom from all types of surface contamination, according to the acceptance criteria of the inspection methods specified in the procedures required by para.
If such indications are observed at the anticipated end of a cleaning operation, continued cleaning shall be performed to reduce the level to the specified limit.
Inspection results shall be documented. Copies of the objective evidence regarding the type s and content of the examination s shall be retained by the employer in accordance with as,e requirements of section of this Requirement.
The inquiry shall be submitted in typewritten form; however, legible, handwritten inquiries will nqs-1 considered. Lead Auditors shall maintain their proficiency through one or more of the following: No part of this document asmee be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
Requirement 11 Test Control. Approved changes created subsequent 200 a baseline shall be added to the baseline. When such an assembly or component part is a commercial grade item, the critical characteristics of the item to be verified for acceptance and the acceptance criteria for those characteristics shall be documented.
Page 4—7 Location Part I, Introduction, Change 1 Definitions of audit, external; audit, internal; inspector; right zsme access; surveillance; and verification added 2 Definition of quality assurance record revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised in its entirety Redesignated from Nonmandatory Appendix 7A-2 and revised Section deleted Section deleted and subsequent sections redesignated Redesignated as Subpart 2.
PD635 ASME NQA-1-2008/1A-2009 Quality Assurance
The item shall be flushed at the design velocity or other flow velocity if specified in the procedure until the screen shows no more than slight speckling as specified in the procedure in qualitative or quantitative terms, such as the number of particles per unit area of the screen and no more than slight rust staining. For those computer programs used for operational control, computer program test procedures shall provide for demonstrating required performance over the range of operation of the controlled function or process.
Such training shall include planning, performing, reporting, and follow-up action involved in conducting audits. To minimize the possible adverse effects aeme halogens, the chemical requirements for water used on components or systems containing austenitic stainless steel or corrosion-resistant alloy shall be as determined by technical evaluation.
ASME NQA EN 核电体系认证_图文_百度文库
The activity shall be described to a level of detail commensurate with the complexity of the activity and the need to assure consistent and acceptable results. Status shall be maintained through indicators, such as physical location and tags, markings, shop travelers, stamps, inspection records, or other suitable means.
These sources were utilized in the development of the criteria in section of Requirement 7. Definitions generic to quality assurance activities are included in Part I, Introduction, sectionTerms and Definitions.
The designee shall be responsible for organizing and implementing receipt controls for permanent and temporary storage. Inquiries shall be submitted in the following format: It provides a foot in the door to the industry; however, it does not relieve the buying organization from going through its vendor qualification process.
NQA-1 – Wikipedia
The status of configuration items resulting from software design shall be maintained current. Guidelines for classifying hydraulic, instrument, and lubrication cleanness are presented in Part III, Subpart 3. These verification functions include the following: NSL provides critical material testing data to members of the nuclear power supply chain; from raw material and parts manufacturers, to engineering and construction firms, to plant operators.
This identification shall relate an item to an applicable design or other pertinent specifying document. Test results for design qualification tests and software design verification shall be evaluated by the responsible design organization.
State the purpose of the inquiry, which would be either to obtain an interpretation of the Standard nqqa-1 to propose consideration of a revision asmee the present Standard. The program shall identify the activities and items to which it 20008. From its initial publication inthe Standard has retained the criteria structure of 10 CFR 50 Appendix B in a portion of the document. Moreau, Vice Chair S. The next edition of this Standard is scheduled for publication in Periodic in-use manual or automatic self-check inuse tests shall be prescribed and performed for those computer programs in which computer program errors, data errors, computer hardware failures, or instrument drift can affect required performance.
Control of Supplier Nonconformances. Section of Requirement 7, Commercial Grade Items and Services, contains criteria applicable to 10 CFR Part 50 for nuclear power plants but provides sufficient quality criteria for the facilities identified in Part 1, Introduction, sectionApplicability.
Competence of personnel for performance of the various auditing functions shall be developed by one or more of the following methods: Facilities used for dual storage are not required to satisfy the requirements of para. If, based on the inquiry information submitted, it is the opinion of the Committee that the inquirer should seek assistance, the inquiry will be returned with the recommendation that such assistance be obtained.
The tests performed shall obtain the necessary data with sufficient accuracy for evaluation and acceptance. Design inputs shall be specified on a timely basis and translated into design documents. Control of Supplier-Generated Documents.
Responsibility for the control of further processing, delivery, installation, or use of nonconforming items shall be designated in writing. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters hqa-1, nor assumes any such liability.
Special handling tools and equipment shall be inspected and tested in accordance with procedures at specified time intervals or prior to use. Summary Table for Cleanness Classes.