Preferred supplier of ASTM A / ASME SA / Seamless and Welded Ferritic Stainless Steel Tubing because of widest variety of alloy steel pipe/tube. ASTM A – Download as PDF File .pdf), Text File .txt) or read online. Standard Speciļ¬cation for Seamless and Welded Ferritic and Martensitic Stainless Steel. Leoscor Alloys is one of the Renowned manufacturers & exporter of ASTM A SS Seamless Tubes, SS UNS S Tubes, Seamless Round Tubes, .

Author: Mikazahn Golar
Country: Syria
Language: English (Spanish)
Genre: Automotive
Published (Last): 11 September 2016
Pages: 478
PDF File Size: 13.80 Mb
ePub File Size: 12.19 Mb
ISBN: 704-1-63483-539-6
Downloads: 55293
Price: Free* [*Free Regsitration Required]
Uploader: JoJohn

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Active view current version of standard. Work Item s – proposed revisions of this standard.

Two of these grades, TP and UNS S Table 1are amenable to hardening by heat treatment, and the high-chromium, ferritic alloys are sensitive to notch-brittleness on slow xstm to ordinary temperatures.

DF or smal diameter or thin walls, or both, tubing, where many drawing passes are required, a carbon maximum of 0. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Within the text, the SI units are shown in brackets. Less than 2 in.

AFor longitudinal strip tests a deduction of 0. Grade TP is used primarily for hot-water tank service and does not require post-weld heat treatment to prevent attack of the heat affected zone. CW hen intergranular corrosion testing is specified, the test will be Practices Ausing samples prepared as agrred upon between the seller and the purchaser.

ATPS is a lower carbon version of TP that has a lower tensile strength but improved ductility and qstm toughness. The tubes shall have a hardness number that will not exceed the prescribed Brinell and Rockwell hardness values. Most of these grades are commonly known as the “straight-chromium” types and are characterized by being ferromag-netic.

  C106BG DATASHEET PDF

On such sizes a variation in wall thickness of Link to Active This link will always route to the current Active version of the standard. These features should be recognized in the use of these materials. S 75[] 60[] 15 AFor longitudinal strip tests a deduction of 0.

BCalculated elongation requirements shall be rounded asttm the nearest whole number. Two of these grades, TP and UNS S Table1are amenable to hardening by heat treatment, and the high-chromium, ferritic alloys are sensitive to notch-brit-tleness on slow cooling to ordinary temperatures.

Link to Active This link will always route to the current Active version of the standard. A number in parentheses indicates the year of last reapproval.

This abstract is a brief summary of the referenced standard. This standard is issued under the fixed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. Most of these grades are commonly known as the “straight-chromium” adtm and are characterized by being ferromagnetic. These features should be recognized in the use of these materials. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

The following table gives the computed minimum values. Combining values from the two systems may result in astk with the specification. Axtm guide covers standard specification for a number of grades of nominal-wall-thickness, welded ferritic and martensitic stainless steel tubing for general corrosion-resisting and high-temperature service.

ASTM A Stainless Steel tubing standard download

Historical Version s – view previous versions of standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. The steel shall conform to the following tensile properties: The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

  INFORME WARNOCK 1978 PDF

Within the text, the SI units are shown in brackets. Small outside diameter tubes are defined as those less than 0. Work Item s – proposed revisions of this standard.

Grade TP is used primarily for hot-water tank service a26 does not require post-weld heat treatment to prevent attack of the heat affected zone. Grade TP is used primarily for hot-water tank service and does not require post-weld heat treatment to prevent attack of the heat affected zone. Combining values from the two systems may result in nonconformance with the specification. These features should be recognized in the use of these materials.

For lengths over 24ft[7. Two of these grades, TP and UNS S Table 1are amenable to hardening by heat treatment, and the high-chromium, ferritic alloys are sensitive to notch-brittleness on slow cooling to ordinary temperatures.

The steel shall conform to aatm required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, aluminum, copper, nitrogen, titanium, and columbium. AThese tolerances apply to cut lengths up to and including 24 ft[7.

ASTM A268 Stainless Steel tubing standard download

Several mechanical tests shall be conducted, namely: BOvality provisions of Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The number of tubes in a lot heat treated by the continuous process shall be determined from the size of qstm tubes. Referenced Documents purchase separately The documents listed below are referenced within zstm subject standard but are not provided as part of the standard.