For (Withdrawn ). Withdrawn Standard: ASTM A/AM | Developed by Subcommittee: A WITHDRAWN, REPLACED BY A/ AM. This standard is issued under the fixed designation A /A M; the NOTE 1 —A typical ordering description is as follows: ASTM A Annealed Spring Steel Chemical Composition. ASTM A Alloy, Rockwell ( approx), Carbon, Manganese, Phosphorus (max), Sulfur (max), Silicon. , B-

Author: Goltirisar Maran
Country: Cayman Islands
Language: English (Spanish)
Genre: Music
Published (Last): 14 September 2007
Pages: 185
PDF File Size: 18.87 Mb
ePub File Size: 11.40 Mb
ISBN: 283-3-24348-782-1
Downloads: 1578
Price: Free* [*Free Regsitration Required]
Uploader: Gagul

The metric portions of the tables herein list permissible variations in dimensions and mass see Note 1 in SI metric units.

The values stated in each system may a68 be exact equivalents; therefore, each system shall be used independently of the other.

ASTM A / AM – 06 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled

For accuracy in testing, the hardness scales should not overlap. OD maxNo. It is produced to minimum Rockwell hardness requirements, which vary with grade, microstructure and gauge.

This abstract is a brief summary of astmm referenced standard.

ASTM A / AM – 17 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled

It is furnished in the following types as specified: Link to Active This link will always route to the current Active version of the standard. The maximum of the specified carbon range is over 0. Combining values from the two systems may result in non-conformance with the standard.

  DELCO 1111411 DISTRIBUTER PDF

If the minimum temper is over Rockwell C 20 15N The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This standard has been approved for use by agencies of the Department of Defense.

Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled

It is furnished in the following types as specified: It is furnished in the following types as specified:. Combining values from the two system may result in non-conformance with the standard.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Full hard can be produced with either a pearlitic or spheroidized microstructure or a mixture of both. Active view current version of standard. It is produced to a maximum Rockwell hardness. The minimum hardness should be established between the consumer and the producer.

It is produced to a maximum Rockwell hardness. The values listed are not exact aatm of the values listed in the inch-pound tables z684 instead are rounded or rationalized values. Link to Asttm This link will always route to the current Active version of the standard. Last previous edition A — 81e1. zstm

  INTERNATIONAL BUSINESS 4TH EDITION GRIFFIN & PUSTAY PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

The maximum of the specified carbon range is over 0. It is less suitable that No. However, under SI the preferred term is mass.

Within the text, the SI units are shown in brackets. Conformance to SI tolerances is mandatory when the “M” specification is used.

These ratios apply to bending performance of the test specimen. Link to Active This link will always route to the current Active version of the standard. It is produced to minimum Rockwell hardness requirements, which vary with grade, microstructure and gage.

A6844 test and bend test shall be made to conform to the requirements specified.