The full title of ASTM E explains its purpose: “Standard test method for water penetration of exterior windows, skylights, doors, and curtain. ASTM E Report No.: E Rendered to: IMISON USA. Houston, Texas. PRODUCT TYPE: Foam and Plaster Wall System. SERIES/MODEL. Question: “I have read both ASTM E and ASTM E and can’t find any difference between the two test methods. It stands to reason that.
|Published (Last):||17 January 2015|
|PDF File Size:||8.30 Mb|
|ePub File Size:||3.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
The calibrated spray apparatus spray-rack system delivers water to the test specimen at a rate of 5. Some designs are more sensitive than others to this upward moving water.
ASTM E | Water Penetration Testing
This test method does not address these issues. BDG utilizes professional testing equipment that is calibrated to each specific testing standard for accurate results. Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass.
The ASTM E Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference is a testing standard that describes the procedures to determine the water penetration resistance of windows, curtain walls, skylights, and doors when water is applied using a calibrated spray apparatus while simultaneously applying uniform static pressure to opposite sides of the test specimen.
Search Search our news blog.
e3311 It is difficult to simulate the identical complex wetting conditions that can be encountered in service, with large wind-blown water drops, increasing water drop impact pressures with increasing wind velocity, and lateral or upward moving air and water. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Most generic specifications call for a minimum testing pressure of 6.
If you are looking for a reputable second or third-party testing company to perform accurate professional testing, provide concise reports, and help you through the entire process, contact BDG today.
MISSION Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
Hence the adding the specification of Installed test specimens, and specimens in the field. Give us a call to discuss your next project.
The air-pressure differences acting across a building envelope vary greatly. Included diagrams show these differences. We provide testing services throughout the United States from our headquarters located in Xstm, GA. These factors should be fully considered prior to specifying the test pressure difference to be used. Posted on April 20, by admin.
ASTM E 331
In service, the performance will also depend on the rigidity of supporting construction and on the resistance of components to deterioration by various causes, vibration, thermal expansion and contraction, etc.
There is another very similar test method, ASTM Ewhich only allows for the cyclic air pressure procedure. The testing pressure differential is usually determined by the testing specifier.
Categories Click on area of interest below. It is also interesting to note that there are two AAMA standards that refer to these ASTM standards for most of their procedures and are performed in nearly identical fashion. Our products are guaranteed to do their job so you’re free to do yours without the hassles and worries of building and maintaining your own equipment. BDG has extensive knowledge of most building systems and specializes in forensic water intrusion investigations.
The E describes the test specimen being affixed to the air chamber The E describes the air chamber being affixed to the test specimen Hence the adding the specification of Installed test specimens, and specimens in the field. The ASTM E testing is performed by applying water to the exterior of the test specimen while lowering the pressure inside by means of an air chamber built on the inside or opposite side of the test specimen.
Building Diagnostics Group, Inc. In short, the is easier to comply with in the field. Leave a Reply Cancel reply Your email address will not be published.
Your email address will not be published. Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset. For specific hazard statements, see 7.
Failures during quality assurance new construction testing can result in unnecessary d331 that impact your bottom line. Subscribe Subscribe to news updates. This allows us asfm not only properly test fenestrations on new construction projects, but also pinpoint the cause of 3e31 test failures and provide accurate recommendations to achieve successful testing results.
In applying the results of tests by this test method, note that the performance of a wall or its components, or both, may be a function of proper installation and adjustment.