This document uses these configurations. ip unnumbered Ethernet2/0/0 router ospf 1 network area 0. Redistribution Configuration Syntax and Examples. IGRP and EIGRP. OSPF. RIP. Redistributing Static Routes Except Gateway of Last resort in. This article describes some basic OSPF configuration.

Author: Akijind Shaktizilkree
Country: Mauritania
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 23 January 2012
Pages: 213
PDF File Size: 16.9 Mb
ePub File Size: 3.42 Mb
ISBN: 800-6-17482-467-1
Downloads: 35152
Price: Free* [*Free Regsitration Required]
Uploader: Tar

Conciguration IDs are unique numeric identifiers, in dotted decimal notation. Configure the router identifiers for the devices in your OSPF network. Next, you need to define on which interfaces OSPF will run and what networks will be advertised.

To verify if the routing updated were exchanged, we can use the show ip route command. Configure the device interfaces. For example, here is the output of the command on R In this example we have two OSPF areas — area 0 and area 1.

To quickly configure a single-area OSPF network, copy the following commands, paste them into a cohfiguration file, remove any line breaks, change any details necessary to match your network configuration, copy and paste the commands into the CLI at the [edit] hierarchy level, and then enter commit from configuration mode. Because R1 connects only to R2, we only need to establish a neighbor relationship with R2 and advertise directly connected subnet into OSPF.

  APPLIED THERMODYNAMICS BY T.D.EASTOP PDF

Confirm that the Area field displays the value that you configured. Confirm your configuration by entering the show protocols ospf command. You must also create a backbone area if your network consists of multiple areas. Characters IA in front of the routes indicate that these routes reside in different areas.

OSPF configuration

We will use the following network topology:. We can do that using the following sequence of commands:. Then we need to eoutage what network will be advertised into OSPF.

We can verify that by using the show ip ospf neighbor command:. For a single-area OSPFv3 network, include the ospf3 statement at the [edit protocols] hierarchy level. In an autonomous system ASthe backbone area is always assigned area ID 0.

Example: Configuring a Single-Area OSPF Network – TechLibrary – Juniper Networks

If the output does not display the intended configuration, repeat the instructions in this example to correct the configuration. NOTE We have used the router-id 1. To do that, the following configuration on R1 will be used:. To verify if directly connected subnets are really advertised into the different area, we can use the show ip route ospf command on both R1 and R Now R2 should have neighbor relationship with both R1 and R3.

To confirm your OSPFv3 configuration, enter the show protocols ospf3 command. Our goal is to advertise the subnets directly connected to R1 and R3. As you can see from the network topology depicted above, routers R1 and R3 are in the area 0 and area 1, respectively. We can verify that the routers have become neighbors by typing the show ip ospf neighbors command on either router:.

  ALEJANDRO RUELAS GOSSI PDF

Area IDs need only be unique within an AS. Jan 26, upravnik. The network commands entered on both routers include subnets directly connected to both routers.

OSPF basic configuration is very simple. Home About Contact Support our work. First, we need to enable OSPF on both routers.

Configuration du routage ospf – routeur Cisco

This can be done by using the following sequence of commands on both routers:. Configuration of R3 looks similar, but with one difference, namely area number.

R3 is in the area 1. To do that, we need to specify different area ID for each neighbor relationship, 0 for R1 and 1 for R2. All other networks or areas in the AS must be directly connected to the backbone area by area border routers that have interfaces in more than one area.