Unimat SL and DB lathes: unused, boxed examples publication titled: “First Junior Instructions for using The Emco Unimat Universal Machine Tool”. EMCO Hobby Machine Instruction Manuals and Spare Part Lists. Below are links to instruction manuals for various machines. Unimat 3. Spare Parts List. unimat,lathe,belts, manual, book emco, edelstaal,parts, db, sl, unimat 3, mini lathe, db, sl

Author: Zulkihn Dishura
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Love
Published (Last): 7 April 2005
Pages: 396
PDF File Size: 2.77 Mb
ePub File Size: 20.89 Mb
ISBN: 673-8-96592-587-9
Downloads: 40694
Price: Free* [*Free Regsitration Required]
Uploader: Gardagar

The original belts were in the form of coiled-steel wire “springs”, not an ideal material to run against aluminium. Unless specified, all shipments originate from In April the writer met a model engineer who had been given one as a present for his 21 st birthday some 40 years previously. Vintage Flyers, Price uinmat, Acessory catalogs, Paper material.

However, by the mid s the technical literature with USA-market machines was showing two motors: Visit my eBay store. Maple Lake, Minnesota, United States.

Please enter 5 or 9 numbers for the ZIP Code. Unfortunately, this model was not well finished and lacked the delightful detailing of earlier machines: After your purchase, you may perform the checkout process immediately and ebay will calculate the shipping charges.

That section of the base on which the headstock fitted was rectangular in shape, with a flat front, and bored to accept a large “inverted-cone” that allowed the headstock to be rotated or quickly detached. This item will be shipped through the Global Shipping Program and includes international tracking.

Please be sure your E-mail settings will accept my reply. Shipping cost cannot be calculated. Although at first the carriage had no form of lock, later models were given a clamp bolt at the rear that also acted as a form of adjustment to the sliding fit.


The ball races are grease lubricated – using oil will wash the grease out and foul up the inside of the motor, again promoting failure.

EMCO-UNIMAT Model SL Operating Manual

Learn More – opens in a new window or tab Any international shipping is paid in part to Pitney Bowes Inc. In order to provide a vertical feed, the 12 mm threaded headstock spindle and its bearings were mounted within a cylindrical “cartridge”, with a rack, formed along its rear surface, engaged by a splined bar inserted into a hole bored through the top face of the headstock.

The smaller turned-parts on were probably made on a “Swiss Auto” – and ideal machine for making quantities of precision miniature components – with the plain-steel, mm diameter handwheels having a pleasing diamond knurl around their outer edge, tiny micrometer dials engraved into the inner boss and straight pins for hand-grips.

The outside face of the front cone was ground to an abutment flange for items screwed onto the spindle ,anual – although this arrangement may have caused problems unimaat the bearing adjustment, with heavier interrupted cuts tending to tighten the cone and reduce clearances. A central leadscrew was used to drive the carriage up and down the bed rails.

Learn More – opens in a new window or tab. The first kind splined drive-bar used to move the cartridge was fitted with a very short, plain handle but later a black knob was added and finally the handle retaining the ballwas lengthened. The tiny instruction book issued with this model was marked as being the 2nd edition and was originally typed on an A4 sheet, reduced to A5 and bound in grey card.


These charges are the buyer’s responsibility. Emcl there was no provision for aligning the headstock, other than fitting the tailstock ram with a centre and pushing it into the spindle hole – while emxo tightening the locking screw.

To discover which model you have found, invert the machine and look at the underside of the bed: Of course, collectors have moved into the market and very early black-finish machines – and most of the accessories from any year – are very sought after and command high prices. A recent discovery was a Mk. Distribution then moved to an organisation called Emco-Luxalmost certainly a tie up between a long-established German-owned European tool distributor and Maier.

The vertical pillar was This year the number has sky rocketed.

Unimat DB/SL Lathe, Belts, Manual,Links.

Arranged by the simple and effective means of splitting the right-hand half of manuxl casting from front to back, the cross-slide clamp used an M6 socket -headed screw set positioned at the front between feed screw and the right-hand 8 mm-diameter cross slide bar to squeeze the parts together.

This amount is subject to change until you make payment.

By the late s crackle-black finishes were being phased out and Emco followed fashion by producing the majority of the Mk. The first Unimat I bought had no belts.