ENRAF-NONIUS ATG Interface. Tank Gauging Protocols Manual. ENRAF INTRODUCTION. The interface between BBI’s Network // Honeywell Enraf ATG Pdf User Manuals. View online or download Honeywell Enraf ATG Installation Manual. Honeywell Enraf series ATG servo gauge is a reliable, versatile and accurate automatic tank level MB; Honeywell Enraf Servo Gauge ATG Manual.

Author: Zolojora Mooguhn
Country: Somalia
Language: English (Spanish)
Genre: Finance
Published (Last): 28 September 2018
Pages: 458
PDF File Size: 6.82 Mb
ePub File Size: 4.94 Mb
ISBN: 697-2-52988-358-1
Downloads: 78808
Price: Free* [*Free Regsitration Required]
Uploader: Yoktilar

Repeatability test refer to section 4.

Safety Page 10 2. Enrsf x 25 S 6 main shaft with magnet S 7 key for main shaft S 9 terminal compartment cover S 12 terminal block assembly S 13 8 wire cable bushing S 10 wire cable bushing S 17 GPS printed circuit board S set of fuses 10 pc. Use the following procedure for calibration.

Enraf servo ATG install guide |

ATG servo gauges are compact and need only a enrav mounting flange. Documents Flashcards Grammar checker. The resulting difference between measured and desired value will cause a variation in the position of the stepper motor and consequently raise or lower the position of the displacer until the measured value equals the desired value.

A Warning concerns danger to the safety of the technician or user;!

Instruction manual series 854 ATG level gauge

AR Accept reference By giving this command, the level value entered in item RL, is accepted as product level and will be shown on the display. Maintenance Page 40 5. UN Unlock Unlock the gauge. It may damage the electronic circuits. QS in section 6. On product level the displacer is immersed less.


Enraf servo 854ATG install guide

Request for the displacer weight. The electronic compartment contains the following sub-assemblies refer to figure 5. To provide electrical contact between the measuring wire and displacer, thus permitting the enrwf of static electricity and preventing loss of the displacer, the displacer must be secured to the measuring wire. If one of the other two interface measurements is selected, the gauge will remain on that interface measurement till the default measurement I1 is selected.

That should be done in this stage. EX Exit Exit protection level 4. You can define your own level 1 password by entering six characters.

Low level alarm set point.

Honeywell Enraf ATG Manuals

Additional information Do not hesitate to contact Honeywell Enraf or its representative if you require additional information. The type of cable glands that must used: The software for the density measurement is available as an option. Reprogram wire tension protection advised setting: The drum shaft bushing is kept in position by a circlip. Check the O-rings to assure water and enrat protection.

Item Manuwl Description CA Calibrate With this command the displacer is pulled up until it is halted against the tank top reference.


AR By giving this command, the level value entered in item RL, is accepted as level value and will be shown on the display. Caution Keep screw threads free from dirt.

Toggle display format With this item, the toggle display format function display scroll can be enabled or disabled. Remove the drum compartment cover. Check whether the gauge type is set correct; if not, change it.

This method may not be followed when your gauge is used for density measurement via the density displacer. Immediate after the gauge detects that tank loading has finished a SAT is executed to rule out or detect that the gauge is unable to measure the product level due to some failure e.

Check the mounting of the ATG whether it is stable and horizontal.

Open the ball valve. Caution The box in which the arrives also contains the measuring drum. Page 2 Preface Preface This manual is intended for technicians involved with the commissioning and service of the Honeywell Enraf series Advanced Technology Gauge.

If not correct, program the correct displacer area.