Find the user manual and the help you need for the products you own at ManualsOnline. I got an old laptop model MA2 without powersupply. SetIP command to see and change the IP addresses of the console. This command can be used to change both Ethernet connectors and even set a gateway. Requirement: STP (shielded twisted pair) cable with RJ45 connector, min. Cat 5e . To connect Ethernet port 1: Connect one end of an Ethernet cable to the.

Author: Kazikasa Zululkree
Country: Finland
Language: English (Spanish)
Genre: Science
Published (Last): 1 April 2009
Pages: 346
PDF File Size: 13.97 Mb
ePub File Size: 17.95 Mb
ISBN: 939-4-23106-898-3
Downloads: 25036
Price: Free* [*Free Regsitration Required]
Uploader: JoJorr

Hey Mayo, Just found this post. Big Thanks – ebuychance. Where should I solder to on the ma3? I would love to know what you figured out on this. I found your blog a few days ago while looking for a solution to the MA7 power problem.

I can’t seem to figure out what is wrong with this gateway ma2

I found a battery on Amazon for like 22 buck shipped. I have a MA7 that I changed the dc port on.

The easiest way is to bypass the shorted hole and jumper directly to the Diode. And the solder looks good on the motherboard.

Chance Sat Aug 14, In the title bar of the menu you can see the current status of the console. When payday rolls around, I think it’s a good bet it’s getting the battery Glad to hear you got your problem solved!!!! I have a laptop with a similiar problem. Hope that helps somebody. Nanual Sun Apr 25, First the seems to be mounted upside down? You must log in or sign up to reply here. They should do either to solve the problem. Don’t have a good battery to test with and the customer isn’t that interested in buying a new one for a laptop that may have a mainboard issue.

  ITALO CALVINO O VISCONDE PARTIDO AO MEIO PDF

Though you gave no description of your problem I cannot guess where your problem might be.

Mayo Hardware Thu Jun 24, Will check into a MA3 tomorrow, and see what tip I can provide. Newer Post Older Post Home. I have to come back to some problems even when I thought they were hopeless.

Connect Ethernet

So I do have quite a bit of hands on experience. Looking gatwway the picture, the post on the left is where I jumped to. I frigged I would start from the outlet and work my way down the line. The board layout for the MA3 is different then what you have shown. Only a member of this blog may post a comment. Manyal have resoldered, then replaced the DC Jack with no luck. Table of contents of this topic hide.

Gateway Laptop MA2 User’s manual |

Sometimes even the DC Jack is defective. Operating perfect for 1 hour.

I know it takes 3 hands, but you’ll find a way. I see PQ29 markedis this it or are there others? Pulled battery, running on cord only. I have already read the beep code manual and the beep s I’m hearing should mean RAM I have just tried brand new ram and reset them properly and I still get the same problem I’ve been having.

  JIM STOPPANI SHORTCUT TO SIZE PDF

Thanks for your help Ken. I have seen many of these in which the copper for the positive pin is destroyed. No, create an account now. Above comment was basic, gatewway sometimes it caused by hardware failure. Ok is there anything I Can do to get the battery charged.

gateway ma2 upgrades Computers & Internet Questions & Answers (with Pictures) – Fixya

Neil Tue Jun 29, I had initially “fixed” it by re-running solder, which failed 15 min after reassembly. I may have to wait until Monday to pick up a board to see the chips ID, can’t keep all the info in my head. I tried the other power supply and it doesn’t make a hum like mine. So there is only one way to resolve it, by bypassing that section if possible. Sorcerer Tue May 11, Anonymous Mon Apr 26, If it is the type with wires, simply remove from connector, short the POS and NEG terminals of the battery connector while pressing the power button.