5. Newsletter. Before doing anything else, make sure to sign up for the free Energy .. Bedini Mono-Pole Energizer circuit that is extremely similar to the diagram. WHAT IS THE BEDINI SG? Get a copy of the Bedini SG – The Authorized Beginner’s Manual if you want to learn all about the Bedini SG and how to build your. This is a hands-on explanation of how to build a monopole energizer based on John C. Bedini’s patent No. 6,, This system charges lead acid or gel cell.

Author: Goltikus Dougar
Country: Malaysia
Language: English (Spanish)
Genre: Automotive
Published (Last): 19 November 2013
Pages: 324
PDF File Size: 3.21 Mb
ePub File Size: 18.49 Mb
ISBN: 468-1-53269-567-4
Downloads: 30939
Price: Free* [*Free Regsitration Required]
Uploader: Nikokazahn

Connect an amp meter analog or digital in series with the discharge load and connect the load. Originally Posted by Sephiroth I’m trying it energize None of this is hard to do, but it takes patience, not blind passion.

The iron rods are ground on the ends as to deflect the magnetic fields, same as the coil pole piece, angles. All the best in your research!

The bias magnet is to apply a little magnetic field to the rods, the reason is to cause a differential in the magnetic field so recovery takes place easy and the rotor moves out of the field easy. None of these things mean anything. I am a Swiss Tool and Die Maker, have therefor little knowledge in electronics. Bringing out this phenomenon is undeniable proof that “something” else is charging your battery.


For the coil, just use an old solder roll or a bobbin you get wire on, cut and fill the center hole with. However, if the coils are firing independant to each other, then each recovery winding will require its own bridge recifier before being wired in parellel to the capacitor. These books are all available by ordering on-line from Tom Bearden’s or Rick Friedrich’s web-site.

Connect it in series with the same battery you are running the motor on. At least 12″ recommended. The destination batteries are then discharged to 10 volts under working load to prepare for Test 2.

This newly charged battery is then discharged by being connected to a sine-wave inverter and running a watt light bulb for 40 minutesjoules. Connect the secondary charging battery as per the schematic. Mark out on the rotor where the magnets will go. This makes your mechanical inductive coupled oscillator no big deal.

Hi Maks, I agree, and It has been a while since filming. Originally Posted becini ren Its an interesting config. The resistance of the coil is not important, the windings are not important, the magnets are not important.

John Bedini Monopole Generators

A dozen recommended for experimental variations e. The destination batteries reach a charge capacity of 13 volts at 2: There is a learning enefgizer here for those who built this motor the way I said to do it about ten people. Find all posts by kokerich. If the meter reads less than 1 volt, the test passed.


Bedini SSG Monopole Energizer Motor Kit

Energizfr are several things that could be addressed here. Schematics and building tips can be found on the advanced lists and other advanced builders are free to discuss their replications. It is recommended to use high farad capacitors and to discharge them around 2 volts above the charging voltage.

I was very lucky that they let me keep the mono pole part of it. It also helps us see that there are two kinds eneryizer energy going to the charging battery. Another schematic for the Monopole Specifications – Trigger wire: For a battery rated in cold cranking amperes CCA see the manufacturer’s website or contact the manufacturer to obtain the equivalent rating in Ah.

For quicker results, select a 3 to 7 amp hour Ah battery. Lincoln R60 works best but many others monopoke work just fine.

John Bedini Monopole Generators :: Nikola TESLA 3 generations later

All along Keelynet was given the information. Wash you hands after contact with batteries. I was watching the DVD mak 5 gazillionth time and in it JB states that the monopoles machines that don’t use capacitors are an advancment over the capacitor version. I also think that there is something about the mechanical contact in the positive leg of the circuit.