With the patented dry®, interseal has developed a technically and . 8 x 8 x microns ( mils) dry equivalent to. microns ( mils) wet . Interseal Interthane SYSTEMS. COMPATIBILITY. Sep 22 , , SYNTHETIC ENAMEL PAINT, INTERSEAL HSALUMINIUM PART A EGA/20LT, Sri Lanka, Bangalore, LTR, , 35,,

Author: Dajora Mezir
Country: Burundi
Language: English (Spanish)
Genre: Art
Published (Last): 18 January 2017
Pages: 82
PDF File Size: 11.26 Mb
ePub File Size: 20.94 Mb
ISBN: 341-3-12066-345-9
Downloads: 15796
Price: Free* [*Free Regsitration Required]
Uploader: Dami

Interseal HS is suitable for application to a wide range of substrates and aged coatings.

Intercure HS can also be used as a primer for substrates other than blasted steel, e. Thoroughly flush all equipment with International GTA Excessive over application of material on areas such as poorly prepared welds may result in long term stress cracking and so early failure. Over-application should be avoided as thick films intersral not be as good a substrate for topcoat adhesion after ageing as those at the specified thickness. A two component, low VOC, high solids, fast curing anticorrosive epoxy primer.

This intsrseal must only be thinned using recommended International GTA thinners. Zinc Phosphate version also available.

Export Data and Price of paint interseal hs from Bangalore | Zauba

These may be subject lnterseal variation depending on factors such as differences in color and normal manufacturing tolerances. Once the unit has been mixed, it must be used within the working pot life specified.

Prior to paint application, all surfaces should be assessed and treated in accordance with ISO However, these phenomena are not detrimental to anti-corrosive performance. A two component, low VOC, high solids epoxy, pigmented with aluminium to provide enhanced corrosion resistance.

Systems compatibility Intercure HS will normally be applied to suitably prepared steel, e. Number of Components Multi pack 4 Single Pack 2. Interseal dries to form a non-tacky, tough, resilient temporary protective layer. A single component, spray applied, high build, water based coating for direct application over coated substrates and non-ferrous substrates.

  EKONOMIKOS TEORIJOS PAGRINDAI PDF

The use of alternative thinners, particularly those containing ketones, can severely inhibit the curing mechanism of the coating. Absolute measured adhesion of topcoats to aged Intercure HS is less than that to fresh material, however, it is adequate for intersea specified end use. Provides quick cure even at low temperatures often encountered in maintenance interssal.

As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges. Low Temperature Curing 24 Hours 1. Available in colours as well as aluminium and glass flake versions with passivator, to provide additional anti-corrosive barrier protection.

Low molecular weight reactive additives, which will form part of the film during normal ambient cure conditions, will also effect VOC values determined using EPA Method Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.

Work stoppages Intfrseal not allow material to remain in hoses, gun or spray equipment.

INTERCURE 200HS – PART B – 3.79L

A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Surface preparation All surfaces to be coated should be clean, dry and free from contamination. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. The surface may deteriorate to Sa2 standard but must be free from loose powdery deposits. However, if necessary, application over prefabrication blast primers can be performed. Dry time 1 Hours 1 26 Hours 1 48 Hours 1 8 Hours 1.

If the shop primer shows extensive or widely scattered breakdown overall sweep blasting maybe necessary. Additionally, in common with all epoxies Intercure HS will chalk on exterior exposure. Suitable for overcoating within 7 hours in most climatic conditions hence speeding up production and throughput in fabrication shops. Always mix a complete unit in the proportions supplied.

A high solids, low VOC, two component, high build, surface tolerant epoxy coating, Interseal HS provides excellent anticorrosive protection in industrial and offshore environments in both atmospheric exposure and immersion service. Be the first to write a review for this product! At low temperatures, it may be necessary to thin Intercure HS to enable airless apray application to be performed.

  ACER K132 MANUAL PDF

Product Line Interseal 6. Consult International Protective Coatings for further details. Press and move to zoom. Over-application of Intercure HS will extend both the minimum overcoating periods and handling times, and may be detrimental to long term overcoating properties.

If oxidation has occurred between blasting and application of Intercure HS the surface should be reblasted to the specified visual standard. Product Lnterseal Primer Chemistry Epoxy. This product is not available in pale and pastel shades due to a tendency to discolour rapidly.

VOC values are typical and are provided for guidance purpose only.

Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Warning Intercure HS is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions. GTA Do not thin more than allowed by local environmental legislation Mix ratio: Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard but have been allowed to deteriorate under good shop conditions for up to days.

Intercure Ijterseal is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. It is good working practice to periodically flush out spray equipment during the course of the working day. Varnish Hybrid Water base.