ISO was prepared by Technical Committee ISO/TC 35, Paints and .. The test panels shall be dry and free of dust and any other foreign. ISO (E) ISO. Second edition. Paints and varnishes — Performance This is a free 6 page sample. Access the full version . Reference number. ISO (E) ISO. First edition. Paints and varnishes — Performance This is a free 6 page sample. Access.
|Published (Last):||13 June 2004|
|PDF File Size:||12.39 Mb|
|ePub File Size:||3.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Assessment after water immersion 4 h Panel No. Table 5 — Assessment of test panels — Methods and requirements ISO Assessment method Frre before qualification testing Requirement after qualification testing ISO pull-off test To be agreed between the interested parties. For each paint in the paint system, the manufacturer shall provide a product data sheet, PDS see 5. Coating thickness measurements min.
Table isoo is not intended to be comprehensive, nor is the intention that it be used as specification guidelines.
This International Standard places emphasis on high-durability paint systems, with the aim of minimizing maintenance, and hence reducing safety considerations and environmental impact. Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure ISO Such information, and the detailed results of the assessment process, shall be the property of the purchaser but shall not be disseminated by the purchaser without prior agreement from the paint manufacturer.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
At least the following information shall be shown on the label: For dated references, only the edition cited applies. It can also be used for other structures, provided that the selected paints or protective paint systems comply with this International Standard.
ISOIron oxide pigments for paints  Micaceous iron oxide: The cross-section of the scribe line shall be as shown in Figure 3.
Assessment after exposure testing h Panel No. The work of preparing International Standards is normally carried out through ISO technical committees. The paint manufacturer shall carry out routine batch testing on each batch of paint.
For undated references, the latest edition of the referenced document including any amendments applies. In order to establish sufficient corrosion protection and ensure optimum performance of the coating, it is necessary to specify the requirements for the protection paint system s along with the relevant laboratory performance tests to assess its their likely durability. In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.
NOTE 2 See 5. Each of the parties involved shall be entitled to carry out additional checks on any batch to verify the fingerprint. Alternative procedure without low-temperature exposure If specified, an alternative exposure cycle may be used. Adobe is a trademark of Adobe Systems Incorporated.
Optional tests may also be carried out, such as impact resistance, abrasion resistance and crack resistance. The maximum thickness of each coat on each panel shall be: An example of a paint system template is given in Table 2. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.
ISO environmental testing servicesAccelerated Weathering Laboratory
Date of report and signatures: The coating system shall be fully cured in accordance with the manufacturer’s most recent instructions before testing starts.
Protect the backs and edges of the test panels with an appropriate means of protection agreed on between the interested parties. Other methods of surface preparation may be used to represent actual field conditions, as agreed between the interested parties. Reference number ISO In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy.
The main fres of technical committees is to prepare International Standards.
In ISOrelevant requirements are given for the following: International organizations, governmental and non-governmental, in liaison with Jso, also take part in the work. Table 3 —Typical examples of some protective paint systems and their initial fee Substrate Blast-cleaned carbon steel: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces ISO Every care has been taken to ensure that the file is suitable for use by ISO member bodies.
In order to achieve the same performance as indicated by testing, proper application of the paint is essential. The fields of application are specified in Clause 4.
Should third-party certification be requested, an independent laboratory shall be agreed on between the interested parties.