LS datasheet, LS circuit, LS data sheet: LSI – BIT QUADRATURE COUNTER,alldatasheet, datasheet, Datasheet search site for Electronic. LSI LS 30 available from 2 distributors. Explore LSI on Octopart: the fastest source for datasheets, pricing, specs and availability. The LSI Computer Systems LS is a CMOS, bit counter that can be programmed to operate in several View the Manufacturer’s Datasheet. Features.

Author: Mazubei Zugor
Country: Armenia
Language: English (Spanish)
Genre: Environment
Published (Last): 25 July 2008
Pages: 424
PDF File Size: 3.40 Mb
ePub File Size: 3.69 Mb
ISBN: 336-2-11292-945-7
Downloads: 52873
Price: Free* [*Free Regsitration Required]
Uploader: Zulkizahn

In any motor-related application, binary counting is necessary. The LS, as mentioned above, connects to the PIC via an 8-bit data bus, datashwet control bits, 2 optional control bits, and 2 optional flags. These pins can be changed, but the data bus read and write functions will need to be changed to interface with bit lines instead of bytes.

The init function can be modified to utilize other special features of the chip not used here. For instance, if the maximum count datwsheetand CNTR isthen the actual position is out of Using a parallel data bus, a microcontroller can simply read the current count value from the chip, allowing a project to interface with motor encoders without using any additional timers.

Because of this, if running the motor backwards continuously counting downthe value of CNTR will always be between 0 and PR at the current position.


Since this was put in the separate function, other code won’t have to be changed, other than TRIS setups. This c file os7166 various functions used to interface with the LS Note that most pins are active low, and thus must be kept at high at all times unless in use. The value of the PR register is loaded whenever the counter borrows downticks from 0.


Alternatively, at each read the PIC could send back the actual count value. The LS is a 24 bit quadrature counter. As mentioned above, multiple LS can be used which are connected to the same data and control lines, except for chip select, which needs to be separate for datashet chip. All three can be download datashet this zip file. The chip has several other features that can be read about in the datasheet.

(PDF) LS7166 Datasheet download

The chip can also operate in divide-by-n mode, which loads the count register with a fixed value on rollover.

A motor’s encoder can be connected directly to the LS, which will decode and count pulses as the encoder channels change. The A and B inputs normally serve as quadrature inputs, like those which come from a quadrature encoder like those on most motors.

A chip with similar capability is the LSRwhich uses the SPI bus to communicate instead of in parallel, is discussed on separate wiki page. Because of this, the datashdet software must be written so that the read value of CNTR is modded by the maximum count number to find the position.

Personal tools Log in. There are also two pins which output flags when programmed events occur, ls7616 as an overflow. Most other functions will usually not be needed unless special features are needed. This c file simply loops continuously and reads values from the LS Note that at the end of the init function, the counter limit value is loaded into the PR register.


Using the LS Quadrature Counter – Northwestern Mechatronics Wiki

Retrieved from ” http: Note that to use thethe only steps are to setup the pins, call the init function, then call the read function to get a value. The LS communicates with a microcontroller via a bi-directional 8-bit data bus and several control bits. The code in this document only covers divide-by-n binary quadrature mode, and for more advanced features the support code will need to be modified.

Note that the code does not reset to 0 when it reaches PR. This is useful for motor applications, since the fixed value can be set to the number of pulses in a full rotation, and then whenever the count value is read, the exact position of the motor can be known no matter the amount of time that has passed since the last read.

For more info on these features, see the datasheet. The following is a list of registers and the general use of each, even though they are already handled by the code written in a later section.

Views Page Discussion View source History. This number should be changed based on the full rotation count of the encoder in use. In the code below and example schematic, pins B0-B7 are used for the data bus.

Eventually the CNTR will overflow if not reduced.